Fairs and Congresses - Euroguss 2022

Int. Aluminium Pressure Die Casting Competition 2012

The competition has again been organised jointly by the Association of the Aluminium Recycling Industry (Verband der Aluminiumrecycling-Industrie, VAR) and the Organisation of European Aluminium Refiners and Remelters (OEA), supported by the Association of German Pressure Die Casters (Verband Deutscher Druckgießereien) and the Die Casting Technical Committee of the Federal Association of the German Foundry Industry (Bundesverband der Deutschen Gießerei-Industrie, BDG). The aim of this highly regarded competition is to demonstrate the high quality standards aluminium die castings have to offer and publicise die-casting-friendly design. The extent to which recycled aluminium is used in the casting is also an important aspect of the competition.

Thirteen castings were entered; seven originated from Germany with two each from Italy and Austria, and one each from Switzerland and the Netherlands. In this year's competition, attention focussed on process customisation and not on trend-setting innovation as in previous years. This change has signalled a break with traditional entries: new ideas for the future in fields of tooling technology and tooling design are apparent. Experience in series production will lead to new design concepts being developed for the future. One should point out the very great potential of aluminium die casting in lightweight construction that enables the growing demands for sustainable development to be satisfied. The castings submitted were produced mainly from recycled aluminium.

The assessment and choice of the prize-winning castings was carried out by a jury of experts from research and industry. Three prizes were awarded and a further three entries were highly commended.

Aluminium Award

There are two first prizes because both castings exhibit innovative component design using the same technology. One of the components is an extremely thin-walled, intricate and lightweight design whereas the other is extremely thick-walled but thus correspondingly strong. The heavy gauge shows that it is actually possible to produce this structural element reliably by means of die casting, a process that is supposedly not suitable for such parts. The diversity in the possible use of the process to produce innovative die castings can be seen from the differences between the two winning components.

Aluminium Competition 2012Aluminium Competition 2012Aluminium Competition 2012
Aluminium Competition 2012

1st Prize
Mid-section of one-piece gearbox casing with Integrated cast-in gearbox support arms

Martinrea Honsel Germany GmbH, Meschede, Germany
Dimensions (LxBxH): 459 x 726 x 428 mm
Weight: 44.5 kg Alloy: Al Si9Cu3(Fe)
Weight saving (CO2 reduction) plays an important role with this one-piece gearbox casing. The new design eliminates the forged supporting arms. One should mention in particular the integration of functions. Designing the cast component as a die casting (instead of the chill casting originally used) increases the load-bearing capacity and allows higher operational demands to be satisfied in practice.

Aluminium Competition 2012

1st Prize
Longitudinal chassis beam for Audi A8 Space Frame

DGS Druckguss Systeme AG, St. Gallen, Switzerland Dimensions (LxBxH): 700 x 700 x 300 mm
Weight: 5 kg Alloy: Al Si9MgMn
lt is particularly difficult to produce this component accurately because of its complex geometry. Special mention should be given to the high degree of integration of functions in the thin-walled section and this leads to high dimensional accuracy of 0.7 mm. The longitudinal chassis beam is produced by casting as a single piece and joined to other components by welding.

Aluminium Competition 2012

3rd Prize
Lower part of crankcase K48 for BMW motorcycle K1600GT/GTL

TRIMET ALUMINIUM AG, Harzgerode, Germany
Dimensions (LxBxH): 350 x 311 x 506 mm
Weight: 10.68 kg Alloy: Al Si9Cu3
This new design concept will send out a clear message for new ideas in future: die design, redesigning an existing chill casting as a die casting and achieving the benefits of both casting processes in a die casting. The evaluation here took mould technology in particular into consideration.

Zinc Award

ZINK Competition 2012ZINK Competition 2012ZINK Competition 2012
Zink Competition 2012

1st Prize
Control lever from the lifestyle of a household appliance segment
(Haveländische Zinkdruckguss)

Zink Competition 20122nd Prize
Power Connectors
(Artur Monse GmbH & Co. KG

Zink Competition 2012

3rd Prize
Support unit for mechanical components in the medical (Kaspar Lüther Gmbh & Co.KG)

also available in

Youtube Linkedin Xing