B2B Portal for Technical and Commercial Foundry Management
Languages

Foundry Daily News

02. Oktober 2014

ISO P classification

The ISO P classification of workpiece materials includes the metals generally referred to as steels. While steels don’t present obvious machining challenges like materials such as heat-resistant aerospace alloys used in aerospace applications do, steel alloys and irons are the workpiece materials most widely applied across all industries.

This has led to the development of a large selection of steel alloys with differing physical properties that generate a variety of metal cutting performance issues, which in addition to economic considerations of high-volume production demands, make machining of ISO P steels a significant challenge for parts manufacturers as well as the makers of the tools used to machine them.
ISO system

The ISO metalworking workpiece material classification system is divided into six categories – K, S, H, M, N and P. The K group covers cast irons; heat-resistant superalloys including nickel- and titanium-based alloys are in the S group; group H materials are characterised by their hardness and basically include steels hardened to 45-65 HRc; stainless steel alloys with chromium content greater than 12 percent make up the M group; the N category covers nonferrous metals, mainly aluminium as well as copper and brass; and the P classification includes unalloyed, low-alloy, and high-alloy steels, including alloys hardened up to 400HB and stainless alloys with chromium content of 12 percent or less. Some long-chipping malleable irons are also part of the ISO P group.

These materials are classified largely on the basis of their dominant physical properties, which essentially determine how the material reacts to machining, and how in turn machining affects the cutting too. K group metals are characterised by abrasiveness, which accelerates tool wear. Heat-resistant superalloys in the S group generally have poor thermal conductivity, resulting in heat concentration in the cutting zone that can deform a cutting tool. Group H metals are hard, creating great pressure on tools and also generating heat. The M group is subject to strain hardening, in which the workpiece material becomes harder as it is deformed in the cutting process with the increased cutting pressure and heat generation causing notch wear and other problems. Metals in the N category exhibit a tendency to adhere to the cutting tool, which leads to edge build-up, poor surface finish, and cutting tool fracture.

All five ISO groups listed above are each distinguished by a dominant physical property, allowing cutting tools to be engineered to a degree, to counteract the property’s negative effects on the cutting tool. Tools for cutting materials in the H group are biased toward strength, for example, while tools engineered to cut N category metals are sharp and designed to promote chip flow that minimises the occurrence of adhesion.
Workpieces in the ISO P group, however, present more complex challenges. Steels in general and widely differing steel alloys in particular can exhibit more than one or even all of the properties that affect cutting tools, although usually not to an extreme degree. This complicates tool development; in many cases, for example, a sharp-edge tool engineered to counter the adhesion tendencies of a low alloy steel may not be able to withstand the abrasive characteristics of another steel composition. In addition, development of specialised steel alloys continues unabated as manufacturers seek materials matched to the particular performance demands of their customers’ parts.
Understanding metal-cutting

It is difficult to find a productive balance between tool performance properties when machining steel alloys. Striking that balance requires an understanding of the nature of metal-cutting and the interaction between the workpiece material and the cutting tool.
Unlike the way that a knife cuts, the metal-cutting process puts pressure on the workpiece material until it deforms and shears away in the form of a chip. Many collateral effects accompany the shearing action. The mechanical forces required to sufficiently deform the material generate a great deal of pressure as well as heat leading to temperatures as high as 800-900°C. Interrupted cuts or machining parts with hard inclusions subject the cutting tool to impact. Beyond mechanical considerations, the high levels of heat and pressure can catalyse chemical reactions between the cutting material and the workpiece material, producing chemical wear in the form of diffusion or cratering.
Metal-cutting also involves a high level of friction. As the chip is formed and rubs over the tool, it creates friction and tribological effects, with all the forces and interactions producing varying outcomes including tool wear.
Different steels, different tools

The effects of machining on steel workpieces vary with the composition of the steel alloy and the process by which it is manufactured. Unalloyed steels with carbon content less than 0.25 percent, for example, have been developed for applications such as automobile axles that require strength and resistance to impact and fracture. These rolled or forged alloys produce chips that are difficult to break and rub the surface of a cutting tool, producing crater wear and even adhesion problems. Cutting tools for these compositions are designed with sharp edges to more efficiently shear the workpiece material, and also employ coatings to resist chemical wear and provide lubricity to the cutting surface.
On the other hand, high alloyed steels with alloy content over five percent, including elements such as manganese, can be hardened for use in components that require wear resistance and rigidity, such as hydraulic components and machine tool parts. The chips produced generally are easily formed and broken, but the tools machining these alloys are subject to high pressure and high temperatures. If the unmachined workpiece was produced via casting or forging, a rough surface and possible inclusions from the mould require cutting tools with both toughness and resistance to abrasive wear.

Economic considerations

Machining operations aim to produce more parts faster, requiring application of the most aggressive cutting parameters possible. However, economic considerations can play a large role in the selection of cutting parameters. Parts such as aerospace components produced from exotic alloys most often are made in relatively low volumes.

Manufacturers machine the parts at a pace aimed to maximise process reliability and preserve the expensive workpiece materials and costly manufacturing time already invested. As a result, speeds and feeds employed with advanced workpiece materials usually are productive but conservative.
The approach to machining of steel components often is different. Many steel parts are manufactured in high volumes and as quickly as possible to maximise economic returns on relatively simple parts machined from less-expensive workpiece materials. Higher cutting speeds require cutting tool substrates with the ability to retain strength at high cutting temperatures. In light of the growing selection of steel alloys, it can become necessary for manufacturers or machine shops to consult with cutting tool manufacturers to find the tool grade and geometry best suited to a particular application. Ongoing tool development is aimed at creating tools that can cope with the multiple issues presented by steel alloys.
Manufacturers seek tools that are sharper yet stronger, with coatings and geometries designed to overcome the heat, pressure, chemical and adhesion mechanisms of wear.

Environmental consciousness

Environmental sensitivity is a relatively new consideration influencing the choice of machining parameters for steel materials. Many manufacturers are now pursuing environmentally conscious or ‘green’ machining initiatives including reducing energy consumption and minimising the waste generated during the machining process. Although technological machining challenges remain the primary concern when processing exotic metals, environmental concerns are rising in importance when machining steels.
One way to reduce energy consumption is to reduce cutting speeds. In many cases, manufacturers can maintain productivity by proportionally increasing feed rate and depth of cut. In addition to saving energy, such strategies also result in longer tool life. Waste is also reduced in the process with fewer cutting edges and ‘throwaway’ inserts consumed to produce the same number of parts. Lower cutting speeds also generate less heat, which can reduce demand for metalworking coolant, which is an undesirable waste product of the metalworking process.
Conclusion

Since ISO P steels are widely applied on routine parts, machining operations involving the alloys usually are not subject to intense interest and analysis. However, when manufacturers understand that steels present multiple machining challenges that can be overcome with careful tool selection, high part volumes can make even small improvements in machining productivity significant contributors to profitability and environmental preservation.
Seco Tools Australia specialises in providing industry solutions that focus on high productivity, cemented carbide turning tools, milling cutters, grooving tools, drills and indexable inserts.


Source: Ferret.com.au

 

 

Related Articles

Youtube Linkedin Xing